| |
使用マザーボードはGA-D510UDです。
NM10のSATAポートには、KINGSTON SSDNOW 30GBとWD20EARS-00MVWB0を繋いでいます。これらはCDIで認識されています。
このマザーボードにはJMicronのチップが載っていて、SATAが2ポート追加されています。
そのポートの1つ（どちらか忘れました）にMaxtor 6V250F0を繋いでいたのですが、そのときはCDIで認識されていました。
その後6V250F0をWestern Digital WD20EARS-22MVWB0に換装したのですが、CDIで認識されません。JMicronチップの2ポートのうちどちらに繋いでも認識されません。
smartmontoolsを試したところ、-T permissiveを2回つけることによってSMART値を読むことができました。
C:\Windows\system32>smartctl -a sda
smartctl 5.42 2011-10-20 r3458 [i686-w64-mingw32-win7(64)-sp1] (sf-win32-5.42-1)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
Smartctl: Device Read Identity Failed: Function not implemented
A mandatory SMART command failed: exiting. To continue, add one or more '-T perm
issive' options.
C:\Windows\system32>smartctl -a sda -T permissive
smartctl 5.42 2011-10-20 r3458 [i686-w64-mingw32-win7(64)-sp1] (sf-win32-5.42-1)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
Smartctl: Device Read Identity Failed: Function not implemented
=== START OF INFORMATION SECTION ===
Device Model: [No Information Found]
Serial Number: [No Information Found]
Firmware Version: [No Information Found]
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: [No Information Found]
ATA Standard is: [No Information Found]
Local Time is: Fri Feb 17 17:33:56 2012
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 82-83 don't show if SMAR
T supported.
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 85-87 don't show if SMAR
T is enabled.
A mandatory SMART command failed: exiting. To continue, add one or more '-T perm
issive' options.
C:\Windows\system32>smartctl -a sda -T permissive -T permissive
smartctl 5.42 2011-10-20 r3458 [i686-w64-mingw32-win7(64)-sp1] (sf-win32-5.42-1)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
Smartctl: Device Read Identity Failed: Function not implemented
=== START OF INFORMATION SECTION ===
Device Model: [No Information Found]
Serial Number: [No Information Found]
Firmware Version: [No Information Found]
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: [No Information Found]
ATA Standard is: [No Information Found]
Local Time is: Fri Feb 17 17:34:18 2012
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 82-83 don't show if SMAR
T supported.
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 85-87 don't show if SMAR
T is enabled.
Checking to be sure by trying SMART RETURN STATUS command.
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (37560) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off supp
ort.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_
FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always -
0
3 Spin_Up_Time 0x0027 172 168 021 Pre-fail Always -
6366
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always -
1911
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always -
0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always -
0
9 Power_On_Hours 0x0032 089 089 000 Old_age Always -
8622
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always -
0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always -
0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always -
26
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always -
30
193 Load_Cycle_Count 0x0032 195 195 000 Old_age Always -
17204
194 Temperature_Celsius 0x0022 121 098 000 Old_age Always -
29
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always -
0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always -
0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline -
0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always -
0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline -
0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA
_of_first_error
# 1 Short offline Completed without error 00% 13 -
# 2 Short offline Completed without error 00% 13 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
sdbとsdcについては、smartctl -a sdbで読むことができます。
CDIの認識は以下のような感じです。
-- Controller Map ----------------------------------------------------------
+ 標準デュアル チャネル PCI IDE コントローラー [ATA]
- ATA Channel 0 (0)
- ATA Channel 1 (1)
+ Intel(R) ICH7R/DH SATA AHCI Controller [ATA]
- KINGSTON SSDNOW 30GB
- WDC WD20EARS-00MVWB0
+ GIGABYTE GBB36X Controller [SCSI]
- WDC WD20EARS-22MVWB0 SCSI Disk Device
-- Disk List ---------------------------------------------------------------
(1) KINGSTON SSDNOW 30GB : 30.0 GB [1-1-0, pd1]
(2) WDC WD20EARS-00MVWB0 : 2000.3 GB [2-1-1, pd1]
また、Hard Disk Sentinelをインストールしてみたところ、全てのディスクのSMART値を読むことができています。
CDIでも読めるようにならないでしょうか。
|
|
